Service-Grip dead-ends, manufactured from aluminum clad steel and copper clad steel wire, are designed for the termination of bare aluminum and copper based conductors used for house service connections.
Service-Grip dead-ends, manufactured from aluminum clad steel and copper clad steel wire, are designed for the termination of bare aluminum and copper based conductors used for house service connections.
Add:Dazhoucun Industrial Park, Chengyang District, Qingdao, China.
Tel:+86 13608965318 +86 13668890402
Fax:+86 532 88721733
E-mail:sales@powtech-cn.com
Service Grip Dead-end
General recommendations
Service-Grip dead-ends, manufactured from aluminum clad steel and copper clad steel wire, are
designed for the termination of bare aluminum and copper based conductors used for house service connections. The dead-end is recommended for house service by reason of minimum length, maximum economy and neat appearance.
Rated holding strength
The Service-Grip dead-end is designed as a limited tension Dead-end. Manufacturer will be pleased to
advice on the holding strength of individual fittings. The following information will be needed:
Conductor: Diameter
Lay direction
Holding Strength required
Length of span
Tapping
Tapping over the applied legs of Service-Grip dead-ends is not recommended. Taps can be made on the conductor ahead of the dead-end, or the conductor can continue through the crossover point of fitting, with connectors applied to the continued tail.
Material used
Service-Grip dead-ends are made of material compatible with the conductor to which they are applied.
Application and inspection
Ensure the correct size fitting is used. For detailed method of installation refer to application
instructions. Service-grip dead-ends should not be re-used after original installation
Recommended fittings
Service-Grip dead-end loops are designed for use with a variety of hardware and insulators, all of which should have smoothly contoured surfaces and adequate groove widths and loop diameters.
Production Characteristics
l Crossover Marks: Indicate starting point for application
l Color code: assists in identification of strands size.
l Identification label: Shows catalogue number and strand diameter range.
l Lay direction: Must be same as that of the outer layer of the strand to which it is applied
SG-1500 Series - Bare Conductor
Product model | Cable range (In.) | ACSR | AAC (All-Al.) | AAAC (All-Al. Alloy) | Comp. ACSR | Max. Neck Dia. (in.) | Wt. Per 100 (lbs) | Unit Per carton | Length (inches) | Color code | |
Min. | Max | ||||||||||
SG-1500 | 0.169 | 0.198 | #6, 6/1 | #6, 7W | #6, 7W | #6, 6/1 #6, 7W | 2-3/8 | 8 | 300 | 11 | Blue |
SG-1501 | 0.199 | 0.224 | #5, 6/1 | #4, Solid | #5, 7W | #4, 7W | 2-3/8 | 9 | 300 | 12 | White |
SG-1502 | 0.225 | 0.257 | #4, 6/1 #4,7/1 | #4, 7W | #4, 7W | #4, 6/1 #4,7/1 | 2-3/8 | 10 | 300 | 13 | Orange |
SG-1503 | 0.258 | 0.289 | #3, 6/1 | #3, 7W #2, Solid | #3, 7W | #3, 6/1 #2,7W | 2-5/8 | 13 | 200 | 14 | Black |
SG-1504 | 0.290 | 0.325 | #2, 6/1 #2,7/1 | #2, 7W | #2, 7W | #2, 6/1 1/0,7W | 2-5/8 | 14 | 200 | 15 | Red |
SG-1505 | 0.326 | 0.360 | #1, 6/1 | #1, 7W | #1, 7W | #1, 6/1 1/0,7W | 2-5/8 | 15 | 200 | 17 | Green |
SG-1506 | 0.361 | 0.400 | 1/0, 6/1 | 1/0, 7W | 1/0, 7W | 1/0, 6/1 2/0,7W | 2-7/8 | 28 | 100 | 19 | Yellow |
SG-1507 | 0.401 | 0.450 | 2/0, 6/1 | 2/0, 7W | 2/0, 7W | 2/0, 6/1 3/0,7W | 2-7/8 | 31 | 100 | 21 | Blue |
SG-1508 | 0.451 | 0.510 | 3/0, 6/1 | 3/0, 7W | 3/0, 7W | 4/0, 7W | 2-7/8 | 33 | 100 | 23 | Orange |
SG-1509 | 0.511 | 0.580 | 4/0,6/1 4/0,18/1 | 4/0, 7W | 4/0, 7W | 4/0, 6/1 | 3 | 37 | 100 | 26 | Red |
